Ash Vacuum FAQs – Commonly Asked Questions and Answers
 Why does the nozzle get clogged and how can
I prevent
this from happening?
Why can’t I take out large pieces?
Why is the hose so stiff?
Why doesn't my Ash Vac have suction?
How do I clean the filters?
How often do I have to clean the filters?
How often should I change the filters?
Can I wash the filters?
Why are there burn holes in my primary filter?
Can I use this vacuum for other things?
How full can I fill the vacuum?
Can I take out HOT COALS?
Why does the nozzle get clogged and how can I prevent this from happening?
Use the proper technique to prevent, or minimize, clogging. Do not lower the nozzle directly on top of a pile of ash because larger chunks of charcoal and unburned material will clog the nozzle. Instead, rest the tip of the nozzle directly on the firebrick and hold it so there is a narrow gap that allows only small ash particles to be sucked in. Move the nozzle in small circular motions while maintaining contact with the firebrick surface. The ash is actually removed from the bottom and not the top. Larger pieces of wood or charcoal, etc. can be left in the stove and burned at a later time. Larger particles or materials are not meant to be removed with this vacuum.
If the nozzle gets clogged, DO NOT use your fingers to clean it out because it may be very hot. The proper way to unclog it is to tap it gently on the firebrick, or base of the fireplace or stove.
back to top
Why can’t I take out large pieces?
The vacuum is designed to remove only fine ash. Larger pieces are more likely to contain hidden hot embers, which can damage the primary filter. These larger pieces should be left in the stove or fireplace and burned at a later time. Be sure to use proper nozzle technique to prevent large pieces from being vacuumed.
back to top
Why is the hose so stiff?
The hose is a bit unwieldy because it is made to handle the possibility of warm coals and embers. It is flame retardant. It should be positioned so that the hose has a natural curve from the vacuum to the nozzle that is put inside of the stove or fireplace. Do not position the vacuum so that a kink forms in the hose or else it will cut off the suction. The motor is cooled by external air so if the nozzle does become clogged, it will not damage the motor.
back to top
Why doesn't my Ash Vac have suction?
Time to empty the canister and/or clean the filters.
back to top
How do I clean the filters?
This is a simple and clean operation. You don’t even have to open the canister. Remove the brass screw-on cap on the top of the Ash Vac, and whiggle the agitator rod back and forth (not up and down) for a few minutes. This knocks ash that has been accumulating on the primary filter off, back into the canister. Be sure to put the cap back on and hand tighten.
If this type of cleaning doesn’t result in your Ash Vac returning to full suction, you will need to clean the primary filter. To do this, you have to take the lid off, and you should do this outside, or in a workspace you don’t mind getting a little dirty. Using a flat screwdriver, losen the band clamp that holds the primary filter in place. Remove it. Then do the same with the inner, secondary filter. Using another vacuum, vacuum the ash out of the filters to clean them. Reinstall, and you’re good to go!
back to top
How often do I have to clean the filters?
Typically after 60-80 gallons of ash has been collected by the vacuum.
back to top
How often should I change the filters?
Changing of the filters is determined by the use and care given. We recommend that the filters be changed after about 100 gallons of ash have gone through the vacuum.
back to top
Can I wash the filters?
No. Both filters are specially coated and if they are washed, the finish will be removed and they will not operate properly.
back to top
Why are there burn holes in my primary filter?
Proper use of your Ash Vac will prevent this from happening. While the primary filter is fire-resistant to 1,000 degrees, large red-hot embers pressed up against it with fast circulating air fanning the temperature higher can cause burn holes. The Ash Vac is designed for “warm ash” NOT hot embers.
This concern is more prevalent with pellet stoves, although it can also happen with regular wood burning fireplaces. The best protection from this type of damage is to allow burnt material to completely cool before vacuuming, and using the nozzle as we recommend to only permit fine ash particles into the vacuum. Hold the tip of the nozzle directly against the firebrick at an angle that only permits fine ash, not large chunks, to enter the nozzle. Vacuum ash from the bottom – not from the top of a pile where red hot embers are more likely to be encountered.
back to top
Can I use this vacuum for other things?
No. This vacuum is only designed for ash. If it is used as a regular shop vacuum for materials that could be flammable and then used in a stove and live embers are removed, a fire could result.
back to top
How full can I fill the vacuum?
We recommend emptying the vacuum when the ash level is as high as the port on the side of the canister. When the ash gets this high, you will usually notice a slight reduction in suction because of the reduced area for depositing the ash in the canister.
back to top
Can I take out HOT COALS?
No. Our Ash Vacs are designed for cool to warm ash removal ONLY. Do NOT use one to pick up hot embers.
back to top
|
